Continuing with our systematic approach to wall finishing, we'll now apply the tile pattern across the remaining restroom walls. The next target is the sidewall positioned behind the toilet area. While you may notice both the toilet and urinal visible in this view, this occurs because we're viewing through the toilet partition—a common visual occurrence when working with transparent or sectional views in architectural software.
We'll employ the Split Face command once again, leveraging our established methodology. Since we've already determined the specifications for our three distinct zones, we'll maintain the consistent height of five feet six inches for the primary tile section. Note that this particular wall appears significantly larger in our current view because we're examining the men's room east elevation—encompassing the entire wall span shown here.
Strategic planning becomes crucial at this juncture. Rather than extending the tile pattern across the entire wall length, we need to establish precise boundaries. The goal is to run the pattern from this specific point to that designated endpoint, avoiding any extension into the adjacent lobby area. This precision prevents inadvertent over-application of finish materials, which can lead to both aesthetic inconsistencies and cost overruns. When examining how walls are constructed in most architectural software, it's surprisingly easy to extend boundary lines beyond your intended scope.
For this application, we'll work with approximately 20 feet of coverage. While this measurement may require fine-tuning as we progress—particularly when coordinating with the adjacent women's restroom (Room 202 or 102, depending on your floor numbering system)—it provides a solid starting framework. I'll establish the first boundary line at this 20-foot mark, then drop the vertical boundary to create our working parameters.
This process creates the precise boundary we discussed earlier. Upon completing this sketch phase, you'll observe one clearly defined split area. However, if the height appears incorrect at this stage, adjustment is straightforward. We'll correct that measurement to our standard five feet six inches, then execute the second split operation.
Working within these newly established boundaries, we can now define the one-foot accent band across the upper section. Precision becomes increasingly important here—while we achieved close alignment, exact measurements ensure professional results. Subsequently, we'll add the six-inch base trim across the bottom section, creating our three-zone tile pattern.
Critical technique note: always ensure these boundary lines connect properly. You'll notice this particular wall required a two-stage approach because the natural wall break didn't align with our desired tile boundaries. This situation frequently occurs in real-world applications, making this methodology essential for professional results.
Upon completing the sketch, we now have three distinct panels ready for material application. An added benefit: the adjacent women's restroom automatically inherits this same pattern since both spaces share the common wall structure. When applying materials, exercise caution with the Select by Face function—accidental double-clicking often selects unintended surfaces, requiring additional correction time.
During the material application phase, always verify which material remains active in your selection tool. In this case, the base material appears as the default since it was our most recent selection. Working systematically, apply each of the three materials to their designated zones, observing how changes automatically reflect in both restroom views simultaneously.
With proper execution, both views should display consistent results with minimal cleanup required. This systematic approach ensures both efficiency and accuracy across multiple wall surfaces.
Moving forward with our established methodology, we'll address walls with different functional requirements. The men's south elevation presents a distinct scenario—we'll apply full tile coverage to the wet walls (those exposed to regular moisture), but limit the finish to base trim only on the dry walls, specifically the door wall and the sidewall adjacent to the sink area. This selective approach reflects both practical maintenance considerations and budget consciousness, as comprehensive tile installation represents a significant material investment.
The wall configuration here simplifies our process—unlike the previous complex boundary situation, this represents a single, continuous surface requiring no segmented approach.
Beginning with base trim application, we'll again utilize the Split Face command to establish the necessary boundaries. Focus on defining the primary section here, followed by this smaller adjacent area. Always verify dimensional accuracy during this phase—close approximation often suffices during initial layout, with fine-tuning available throughout the process.
Upon completing the sketch, material application can proceed. Occasionally, wall intersections don't resolve as anticipated—this represents normal software behavior rather than user error. When this occurs, we can address the adjacent wall separately to maintain visual continuity of the base trim across the bottom edge.
For efficiency, complete all Split Face operations on remaining walls before beginning the painting phase. This batch approach minimizes tool switching and maintains workflow momentum. The pattern we've established provides a clear visual guide for consistent application across all surfaces.
After finishing the sketch phase, material verification becomes essential. Always confirm which material appears active in your selection tool—in this instance, we're working with the four-inch tile. Subsequently, we'll apply the four-by-eight field tile, followed by the six-inch base trim to both designated areas. Double-checking your pattern ensures the final result aligns with your design intent and maintains visual consistency throughout the space.
The completed pattern should integrate seamlessly across all surfaces. With these techniques mastered, you can efficiently apply the same methodology to the remaining restroom walls, remembering that entrance walls and adjacent surfaces typically receive base trim only, maintaining the cost-effective approach while ensuring appropriate moisture protection where needed.